kascesteam.blogg.se - Cerec milling

#Cerec milling manual
#Cerec milling full
#Cerec milling software

When the water is due to be changed, a message window appears on your monitor to remind you that it is time to change the water.Īll milling additives contain a biologically degradable preservative. Replace the ball pressure screw every 500 clamping operations.Īn excessively high ceramic and/or base metal content in the cooling water will damage the pump and milling drives. The high clamping forces cause wear of the ball pressure screw. If you find the tank cap, tank drain or filter insert hard to open by hand, use the tank cap opener. When operating a CEREC 3 milling unit and a CEREC MC XL Premium Package milling unit in the same room, be careful not to confuse the block screw of the CEREC 3 with the ball pressure screw of the CEREC MC XL Premium Package. When milling models, a large number of chips collect in the milling chamber.Įach time a model block is milled, remove the chips from the milling chamber by hand.īefore removing them, squeeze the chips so that any stored water is released into the cooling circuit.ĭo not confuse the block screw with the ball pressure screw

If the jets of water do not strike the instruments, carefully remove any foreign particles from the water nozzles with a probe.īe aware chips gathered in the milling chamber.

Clean the clamping cones of the instruments according to the cleaning set instructions.

#Cerec milling manual

Clean the manual block fixing according to the cleaning set instructions.

Once a week or after every forth water change: If the error message does not disappear even after you have performed the prompted action, contact our servicing team. You must observe error messages shown on the display. Have maintenance performed on your unit annually by trained technical personnel / a service engineer. Some countries have legal regulations which require regular safety inspections of electrical devices or systems by the operator. MC XL – The ultimate in ‘extra fine’ grinding and milling in just a few minutes!

‘Extra-fine’ grinding option available.

Convenience with 4 motors and a user-friendly touchscreen.

Grind/mill all CEREC and CEREC Premium indications and materials.

Complete chairside and lab spectrum for block sizes up to 85mm.

The dry dust can easily be removed using a short, integrated cleaning program.

And there is no difference in quality between dry and wet milling processes. Dry milling saves a considerable amount of time, as the restoration does not need to be dried before sintering – thus enabling the chairside procedure. The new machine can be used for both wet and dry processing, one straight after the other. The new CEREC grinding and milling machines come equipped with a device to vacuum up the mill shavings as well as new precision tools.

#Cerec milling full

Meike Tramitz, patient from Gießen Outstanding restorations now also with full contour zirconia With CEREC I got a complete crown in just one visit – without a temporary or follow-up visits. “Treatment often used to take a long time. Our new milling and grinding units can also dry mill, making solid zirconia restorations in a single visit possible!

Even very fine fissures are very precisely prepared and the edges are very even. Grinding and milling the restoration design is extremely precise, giving the restorations smooth surfaces.

#Cerec milling software

The milling and grinding units and the CEREC software are optimally synchronised with one another.

Possiblity to produce Guide 2 surgical guides.

Convenience with four motors and a user-friendly touchscreen.

Complete chairside and labside spectrum for block sizes of up to 85 mm.

The dry dust can easily be removed using a short, integrated cleaning programme. There is also no difference in quality between dry and wet milling processes. Dry milling saves a considerable amount of time because the restoration does not need to be dried before sintering, enabling the chairside procedure. The CEREC MC XL can be used for both wet and dry processing.

The CEREC grinding and milling machines come with a vacuum cleaner for mill shavings and precision tools. Take advantage of the convenience of the 4 motors, optional ‘extra-fine’ grinding, and a user-friendly touchscreen. It is also suitable for all CADCAM materials (plastic, ceramic and metal). The range of indications include inlays, onlays, crowns, veneers, bridges, abutments and drilling guides, as well as grinding of all practice laboratory indications with the CEREC MC XL Premium. Milling and grinding units can also dry mill, making solid zirconia restorations in a single visit possible!